National foreword

This British Standard is the UK implementation of EN ISO 19085‑12:2024. It is identical to ISO 19085‑12:2024. It supersedes BS EN ISO 19085‑12:2021+A11:2023, which is withdrawn.

The UK participation in its preparation was entrusted to Technical Committee MTE/23, Woodworking machines.

A list of organizations represented on this committee can be obtained on request to its committee manager.

Contractual and legal considerations

This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be accepted by BSI in relation to the adequacy, accuracy, completeness or reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law.

This publication is provided as is, and is to be used at the recipient’s own risk.

The recipient is advised to consider seeking professional guidance with respect to its use of this publication.

This publication is not intended to constitute a contract. Users are responsible for its correct application.

This publication has been prepared under a mandate given to the European Standards Organizations by the European Commission and the European Free Trade Association. It is intended to support requirements of the EU legislation detailed in the European Foreword. A European Annex, usually Annex ZA or ZZ, describes how this publication relates to that EU legislation.

For the Great Britain market (England, Scotland and Wales), if UK Government has designated this publication for conformity with UKCA marking (or similar) legislation, it may contain an additional National Annex. Where such a National Annex exists, it shows the correlation between this publication and the relevant UK legislation. If there is no National Annex of this kind, the relevant Annex ZA or ZZ in the body of the European text will indicate the relationship to UK regulation applicable in Great Britain. References to EU legislation may need to be read in accordance with the UK designation and the applicable UK law. Further information on designated standards can be found at www.bsigroup.com/standardsandregulation.

For the Northern Ireland market, UK law will continue to implement relevant EU law subject to periodic confirmation. Therefore Annex ZA/ZZ in the European text, and references to EU legislation, are still valid for this market.

UK Government is responsible for legislation. For information on legislation and policies relating to that legislation, consult the relevant pages of www.gov.uk.

Compliance with a British Standard cannot confer immunity from legal obligations.

This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2024.

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

ISO draws attention to the possibility that the implementation of this document may involve the use of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s) which may be required to implement this document. However, implementers are cautioned that this may not represent the latest information, which may be obtained from the patent database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.

Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 4, Woodworking machines, in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 142, Woodworking machines – Safety, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).

This second edition cancels and replaces the first edition (ISO 19085‑12:2021), which has been technically revised. The main changes are as follows:

the Scope has been revised to specify that machines are intended for continuous production use, and other workable materials have been added;
the list of significant hazards has been moved to the new Annex A;
the feed chains greasing mode (MODE 3) has been added in 4.6.2;
subclause 6.2 has been updated and a new full noise test code has been added in Annex F;
optional workpiece supporting devices have been added to the Scope, Clause 3 and 5.10.6 to 5.10.9.

A list of all parts in the ISO 19085 series can be found on the ISO website.

Any feedback or questions on this document should be directed to the user’s national standards body. A complete listing of these bodies can be found at www.iso.org/members.html.

Introduction

The ISO 19085 series provides technical safety requirements for the design and construction of woodworking machinery, as well as for the content of the relevant instruction handbook. It concerns designers, manufacturers, suppliers and importers of the machines specified in the Scope.

This document is a type-C standard as stated in ISO 12100:2010.

This document is of relevance, in particular, for the following stakeholder groups representing the market players with regard to machinery safety:

machine manufacturers (small, medium and large enterprises);
health and safety bodies (regulators, accident prevention organisations, market surveillance etc.).

Others can be affected by the level of machinery safety achieved with the means of the document by the above-mentioned stakeholder groups:

machine users/employers (small, medium and large enterprises);
machine users/employees (e.g. trade unions, organizations for people with special needs);
service providers, e.g. for maintenance (small, medium and large enterprises);
consumers (in case of machinery intended for use by consumers).

The above-mentioned stakeholder groups have been given the possibility to participate at the drafting process of this document.

The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are covered are indicated in the Scope of this document.

When requirements of this type-C standard are different from those which are stated in type-A or type-B standards, the requirements of this type-C standard take precedence over the requirements of the other standards for machines that have been designed and built according to the requirements of this type-C standard.

The full set of requirements for a particular type of woodworking machine are those given in the part of ISO 19085 applicable to that type, together with the relevant requirements from ISO 19085‑1:2021, to the extent specified in the Scope of the applicable part of the ISO 19085 series.

As far as possible, the safety requirements of parts of the ISO 19085 series refer to the relevant subclauses of ISO 19085‑1:2021. Each part contains replacements and additions to the common requirements given in ISO 19085‑1:2021.

All parts of the ISO 19085 series have the same structure, so that reference to ISO 19085‑1:2021 is made always and only from and to the same subclause number at the last indent level.

Clauses 1 to 3 are specific to each part and, therefore, are distinct from ISO 19085‑1:2021, Clauses 1 to 3.

For Clauses 4 to 7 and the annexes, each subclause in ISO 19085‑1:2021 is cited as either:

confirmed as a whole;
confirmed with additions;
excluded entirely; or
replaced with specific text.

This is indicated by one of the following possible statements:

“ISO 19085‑1:2021, [subclause/Annex], applies”;
“ISO 19085‑1:2021, [subclause/Annex], applies with the following additions.” or “ISO 19085‑1:2021, [subclause/Annex], applies with the following additions, subdivided into further specific subclauses.”;
“ISO 19085‑1:2021, [subclause/Annex], does not apply.”;
“ISO 19085‑1:2021, [subclause/Annex], is replaced by the following text.” or “ISO 19085‑1:2021, [subclause/Annex], is replaced by the following text, subdivided into further specific subclauses.”.

Other subclauses and annexes specific to this document are indicated by the introductory sentence: “Subclause/Annex specific to this document.”.

This European Standard was approved by CEN on 28 September 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czechia, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and United Kingdom.

European foreword

This document (EN ISO 19085‑12:2024) has been prepared by Technical Committee ISO/TC 39 "Machine tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines - Safety” the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2025, and conflicting national standards shall be withdrawn at the latest by June 2025.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 19085‑12:2021.

This document has been prepared under a standardization request addressed to CEN by the European Commission. The Standing Committee of the EFTA States subsequently approves these requests for its Member States.

For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this document.

Any feedback and questions on this document should be directed to the users’ national standards body/national committee. A complete listing of these bodies can be found on the CEN website.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United Kingdom.

Endorsement notice

The text of ISO 19085‑12:2024 has been approved by CEN as EN ISO 19085‑12:2024 without any modification.

1 Scope

1.1

This document specifies the safety requirements and measures for manually loaded and unloaded

single-end tenoning machines with a manual feed sliding table,
single-end tenoning machines with a mechanical feed sliding table,
single-end tenoning-profiling machines with mechanical feed,
double-end tenoning-profiling machines with mechanical feed, also designed to be automatically either loaded or unloaded, or both, and
angular systems for tenoning and profiling with mechanical feed

with maximum workpiece height capacity of 200 mm for single-end machines and 500 mm for double-end machines, capable of continuous production use, altogether referred to as “machines”.

1.2

This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.

1.3

The machines are designed to process in one pass one end or two sides, either opposite or perpendicular to each other, of workpieces made of

solid wood, and
materials with similar physical characteristics to wood (see ISO 19085‑1:2021, 3.2); and
only the machines with mechanical feed, made of
fibre-cement,
rock wool and glass wool,
gypsum,
plasterboard,
matrix engineered mineral boards, silicate boards and sulfate boards,
composite materials with core consisting of polyurethane or mineral material laminated with light alloy,
polymer-matrix composite materials and reinforced thermoplastic, thermoset and elastomeric materials,
aluminium light alloy profiles, and
composite boards made from the materials listed above.

1.4

This document is also applicable to machines fitted with one or more of the following devices or additional working units, whose hazards have been dealt with:

sanding units;
fixed or movable workpiece support;
automatic tool changing;
automatic workpiece returner;
glass bead saw unit;
hinge recessing unit;
boring unit;
dynamic processing unit;
sawing unit installed out of the integral enclosure, between machine halves in double-end machines;
foiling unit;
coating unit;
grooving unit with a milling tool installed out of the integral enclosure, between machine halves;
brushing unit;
gluing unit;
sealing unit;
dowels inserting unit;
tongues inserting unit;
inkjet marking unit;
laser marking unit;
labelling unit;
workpiece back-up device (device that is either anti-chipping or anti-splintering, or both);
quick tool changing system;
post-formed edge pre-cutting unit;
additional workpiece support (at either infeed or outfeed, or both);
parallel infeed device on single-end machines;
transversal infeed device on single-end machines;
intermediate workpiece support on double-end machines;
automatic infeed device;
feed chain with dogs.

1.5

This document does not deal with any hazards related to:

systems for automatic loading and unloading of the workpiece to a single machine other than automatic workpiece returner;
single machine being used in combination with any other machine (as part of a line);
use of tools, other than saw blades or boring tools or milling tools for grooving, installed between machine halves and out of the integral enclosure in double-end machines;
use of tools protruding out of the integral enclosure;
chemical characteristics of all materials listed in 1.3 c) to i) and their dust.

1.6

This document is not applicable to machines intended for use in potentially explosive atmosphere nor to machines manufactured prior to its publication.

2 Normative references

3 Terms and definitions

4 Safety requirements and measures for controls

4.1 Safety and reliability of control systems

4.2 Control devices

4.3 Start

4.4 Safe stops

4.5 Braking function of tools

4.6 Mode selection

4.7 Tool speed changing

4.8 Failure of any power supply

4.9 Manual reset control

4.10 Standstill detection and monitoring

4.11 Machine moving parts speed monitoring

4.12 Time delay

4.13 Teleservice

5 Safety requirements and measures for protection against mechanical hazards

5.1 Stability

5.2 Risk of break-up during operation

5.3 Tool and tool fixing design

5.4 Braking

5.5 Safeguards

5.6 Prevention of access to hazardous moving parts

5.7 Impact hazard

5.8 Clamping devices

5.9 Measures against ejection

5.10 Workpiece support and guides

6 Safety requirements and measures for protection against other hazards

6.1 Fire

6.2 Noise

6.3 Emission of chips and dust

6.4 Electricity

6.5 Ergonomics and handling

6.6 Lighting

6.7 Pneumatics

6.8 Hydraulics

6.9 Electromagnetic compatibility

6.10 Laser

6.11 Static electricity

6.12 Errors of fitting

6.13 Isolation

6.14 Maintenance

6.15 Relevant but not significant hazards

6.16 Extreme temperatures

6.17 Substances

7 Information for use

7.1 Warning devices

7.2 Marking

7.3 Instruction handbook

Bibliography

BS EN ISO 19085-12:2024

Woodworking machines. Safety - Tenoning-profiling machines

Current, Under Review

Published:

31 Dec 2024