National foreword

This Published Document is the UK implementation of ISO/TS 8182:2026.

The UK participation in its preparation was entrusted to Technical Committee WEE/36, Qualification of welding personnel and welding procedures.

A list of organizations represented on this committee can be obtained on request to its committee manager.

Contractual and legal considerations

This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be accepted by BSI in relation to the adequacy, accuracy, completeness or reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law.

This publication is provided as is, and is to be used at the recipient’s own risk.

The recipient is advised to consider seeking professional guidance with respect to its use of this publication.

This publication is not intended to constitute a contract. Users are responsible for its correct application.

This publication is not to be regarded as a British Standard.

Compliance with a Published Document cannot confer immunity from legal obligations.

This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 August 2026.

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

ISO draws attention to the possibility that the implementation of this document may involve the use of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s) which may be required to implement this document. However, implementers are cautioned that this may not represent the latest information, which may be obtained from the patent database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.

Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Quality management in the field of welding.

Any feedback or questions on this document should be directed to the user’s national standards body. A complete listing of these bodies can be found at www.iso.org/members.html. Official interpretations of ISO/TC 44 documents, where they exist, are available from this page: https://committee.iso.org/sites/tc44/home/interpretation.html.

Introduction

In quality management systems, welding is classified as a special process — one whose results cannot be fully verified by subsequent inspection and testing. Therefore, consistent quality can only be ensured if the process is properly controlled from the outset. ISO 3834‑2 and ISO 3834-3 outline the quality requirements for fusion welding of metallic materials. They require that manufacturers:

prepare welding procedure specifications (WPS);
qualify these procedures before production;
ensure proper implementation of the WPS during fabrication.

ISO 15607 provides the general framework for specifying and qualifying welding procedures. It introduces several qualification methods but does not provide detailed instructions on:

measuring welding parameters (e.g., arc energy) during qualification;
determining the range of qualification;
translating qualification results into a usable WPS.

In certain situations, for example, when the mechanical or corrosion properties of parent materials and the weld metal can be strongly degraded by the use of the wide range of arc energy rules as given in the standards cited in ISO 15607, it can be appropriate to implement additional provisions that may lead to restrictions. These additional provisions will prevent:

incorrect parameter ranges in WPS documents;
non-compliance with mechanical or corrosion resistance requirements;
inconsistent weld quality across production batches.

This document:

provides practical requirements and recommendations on how to handle welding procedure qualification and specification;
clarifies how to measure and document welding parameters during qualification;
explains how to define and apply qualification ranges effectively.

This document can serve as a contractual reference for the qualification of a welding procedure qualification record and/or the creation of a welding procedure specification.

1 Scope

This document specifies requirements and recommendations for reporting the welding parameters related to the arc energy of a welding procedure qualification record (WPQR) and transferring this data to a welding procedure specification (WPS) for production welding for all arc welding processes.

2 Normative references

3 Terms and definitions

4 Symbols and abbreviated terms

5 Risk levels

6 Measuring welding parameters during WPQR welding

6.1 Calibration, validation of the measuring equipment

6.2 Determination of runs to be measured

6.3 Length of run in pipe and plate

6.4 Weaving width in relation with arc energy

6.5 Arc voltage, welding current, length of the run, welding speed, arc energy and temperature

7 Reporting welding variables to a WPQR

8 Transferring WPQR welding parameters to a WPS

8.1 Welding areas

8.2 Thickness

8.3 Arc-voltage, welding current and welding speed in relation to arc energy

8.4 Relation preheat- and interpass temperature and arc energy

8.5 Weaving width in relation with arc energy

9 Measuring welding parameters during production welding

9.1 Calibration, validation of the measuring equipment

9.2 Determination of several weld areas

9.3 Weaving width in relation with arc energy

9.4 Preheat temperature

9.5 Interpass temperature

Bibliography