National foreword

This British Standard is the UK implementation of EN 507:2026. It supersedes BS EN 507:2019, which is withdrawn.

The UK participation in its preparation was entrusted to Technical Committee B/542/5, Sheet roof and wall coverings.

A list of organizations represented on this committee can be obtained on request to its committee manager.

Contractual and legal considerations

This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be accepted by BSI in relation to the adequacy, accuracy, completeness or reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law.

This publication is provided as is, and is to be used at the recipient’s own risk.

The recipient is advised to consider seeking professional guidance with respect to its use of this publication.

This publication is not intended to constitute a contract. Users are responsible for its correct application.

Compliance with a British Standard cannot confer immunity from legal obligations.

This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2026.

This European Standard was approved by CEN on 17 August 2026.

This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 07 October 2026.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czechia, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and United Kingdom.

European foreword

This document (EN 507:2026) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2027, and conflicting national standards shall be withdrawn at the latest by March 2027.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 507:2019.

EN 507:2026 includes the following significant technical changes with respect to EN 507:2019:

the normative references have been updated;
the list of aluminium alloys suitable for roofing and cladding products has been updated and extended (4.2.1) and a Note has been added to Table 1;
editorial changes/improvements have been introduced.

Any feedback and questions on this document should be directed to the users’ national standards body. A complete listing of these bodies can be found on the CEN website.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United Kingdom.

Introduction

Figure 1 indicates the position of this document in the CEN framework of standards concerning roofing and cladding products of metal sheet.

In this document the performance of the product has been defined in terms of a number of type tests.

The performance of a roof or cladding constructed with these products depends not only on the properties of the product as it is required by this document, but also on the design, construction and performance of the roof or the cladding as a whole in relation to the environment and conditions of use.

Metallic coated aluminium sheet can be easily fabricated. It can be sheared, punched, pressed, drawn, folded, roll-formed without difficulty within the given limits of the properties listed in the respective material specifications.

Coil coated sheet can be fabricated like metallic coated aluminium sheet in most applications, but minimum bend radius, design of forming tools, process temperature etc are chosen according to material properties.

1 Scope

This document specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising).

This document establishes the general characteristics, the definitions and the labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. This document specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs).

This document is applicable to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets.

This document does not specify requirements for supporting construction, design of roof system and execution of connections and flashings.

This document does not apply to self-supporting aluminium sheets that are covered by EN 508‑2.

2 Normative references

3 Terms, definitions, symbols and abbreviations

3.1 Terms and definitions

3.2 Symbols and abbreviations

4 Requirements

4.1 General

4.2 Materials

4.3 Products

5 Sampling and test methods

5.1 Flat products

5.2 Formed (prefabricated) products

6 Designation

7 Marking, labelling and packaging

7.1 Marking and labelling

7.2 Packaging and any special ordering conditions

7.3 Transport, storage and handling

Bibliography