National foreword

This British Standard is the UK implementation of EN 13480‑5:2024. It supersedes BS EN 13480‑5:2017+A2:2021, which is withdrawn.

The UK participation in its preparation was entrusted to Technical Committee PVE/10, Piping systems.

A list of organizations represented on this committee can be obtained on request to its committee manager.

Contractual and legal considerations

This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be accepted by BSI in relation to the adequacy, accuracy, completeness or reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law.

This publication is provided as is, and is to be used at the recipient’s own risk.

The recipient is advised to consider seeking professional guidance with respect to its use of this publication.

This publication is not intended to constitute a contract. Users are responsible for its correct application.

This publication has been prepared under a mandate given to the European Standards Organizations by the European Commission and the European Free Trade Association. It is intended to support requirements of the EU legislation detailed in the European Foreword. A European Annex, usually Annex ZA or ZZ, describes how this publication relates to that EU legislation.

For the Great Britain market (England, Scotland and Wales), if UK Government has designated this publication for conformity with UKCA marking (or similar) legislation, it may contain an additional National Annex. Where such a National Annex exists, it shows the correlation between this publication and the relevant UK legislation. If there is no National Annex of this kind, the relevant Annex ZA or ZZ in the body of the European text will indicate the relationship to UK regulation applicable in Great Britain. References to EU legislation may need to be read in accordance with the UK designation and the applicable UK law. Further information on designated standards can be found at www.bsigroup.com/standardsandregulation.

For the Northern Ireland market, UK law will continue to implement relevant EU law subject to periodic confirmation. Therefore Annex ZA/ZZ in the European text, and references to EU legislation, are still valid for this market.

UK Government is responsible for legislation. For information on legislation and policies relating to that legislation, consult the relevant pages of www.gov.uk.

Compliance with a British Standard cannot confer immunity from legal obligations.

This European Standard was approved by CEN on 9 July 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and United Kingdom.

European foreword

This document (EN 13480‑5:2024) has been prepared by Technical Committee CEN/TC 267 “Industrial piping and pipelines”, the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2024, and conflicting national standards shall be withdrawn at the latest by December 2024.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 13480‑5:2017.

This new edition incorporates the Amendments which have been approved previously by CEN members, and the corrected pages up to Issue 2 without any further technical change. Annex Y provides details of significant technical changes between this European Standard and the previous edition.

This document has been prepared under a standardization request addressed to CEN by the European Commission. The Standing Committee of the EFTA States subsequently approves these requests for its Member States.

For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this document.

This European Standard EN 13480 for metallic industrial piping consists of eight interdependent and not dissociable Parts which are:

Part 1: General;
Part 2: Materials;
Part 3: Design and calculation;
Part 4: Fabrication and installation;
Part 5: Inspection and testing;
Part 6: Additional requirements for buried piping;
CEN/TR 13480‑7, Guidance on the use of conformity assessment procedures;
Part 8: Additional requirements for aluminium and aluminium alloy piping.

Although these Parts may be obtained separately, it should be recognized that the Parts are inter-dependant. As such the manufacture of metallic industrial piping requires the application of all the relevant Parts in order for the requirements of the Standard to be satisfactorily fulfilled.

This European Standard will be maintained by a Maintenance MHD working group whose scope of working is limited to corrections and interpretations related to EN 13480. The contact to submit queries can be found at https://unm.fr/en/maintenance-agencies/maintenance-agency-en-13480/. A form for submitting questions can be downloaded from the link to the MHD website. After subject experts have agreed an answer, the answer will be communicated to the questioner. Interpretation sheets will be posted on the website of the MHD.

Amendments to this new edition may be issued from time to time and then used immediately as alternatives to rules contained herein. These amendments will be consolidated within EN 13480:2024 in accordance with the maintenance system of EN 13480 series approved by CEN/BT Decision C172/2021.

Any feedback and questions on this document should be directed to the users’ national standards body. A complete listing of these bodies can be found on the CEN website.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United Kingdom.

1 Scope

This document specifies the requirements for inspection and testing of industrial piping as specified in EN 13480‑1:2024 to be performed on individual spools or piping systems, including supports, designed in accordance with EN 13480‑3:2024 and EN 13480‑6:2024 (if applicable), and fabricated and installed in accordance with EN 13480‑4:2024.

2 Normative references

3 Terms and definitions

4 Symbols and abbreviations

5 Determination of inspection and testing requirements

5.1 General

5.2 Classification of piping

6 Design review

7 In-process inspection and testing

7.1 General

7.2 Materials and formed pressure retaining parts

7.3 Welding

7.4 Heat treatment

8 Non-destructive testing of welds

8.1 Application of NDT

8.2 Circumferential butt, branch, fillet and seal welds

8.3 Longitudinal welds

8.4 Testing methods

8.5 Reports

8.6 Weld repairs

9 Final assessment and documentation

9.1 General

9.2 Final inspection

9.3 Proof test

9.4 Documentation

10 Declaration

Bibliography

BS EN 13480-5:2024

Metallic industrial piping - Inspection and testing

Current, Under Review

Published:

31 Aug 2024