National foreword

This British Standard is the UK implementation of EN 10283:2019. It supersedes BS EN 10283:2010, which is withdrawn.

The UK participation in its preparation was entrusted to Technical Committee ISE/111, Steel Castings and Forgings.

A list of organizations represented on this committee can be obtained on request to its secretary.

This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.

Compliance with a British Standard cannot confer immunity from legal obligations.

This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2019.

This European Standard was approved by CEN on 14 December 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

European foreword

This document (EN 10283:2019) has been prepared by Technical Committee ECISS/TC 111 “Steel castings and forgings”, the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2019, and conflicting national standards shall be withdrawn at the latest by September 2019.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 10283:2010.

In comparison with EN 10283:2010, the following significant technical changes were made:

alignment with the structure of EN 1559‑1:2011, Founding — Technical conditions of delivery — Part 1: General and EN 1559‑2:2014, Founding — Technical conditions of delivery — Part 2: Additional requirements for steel castings;
new grade (GX20Cr14) added;
Table A.1: welding group added.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

Introduction

This document retains the same format for clauses as EN 1559‑1:2011 and EN 1559‑2:2014. It is intended to be used in conjunction with these documents. Where no text is given under a clause heading, the corresponding clause of EN 1559‑1:2011 or EN 1559‑2:2014 applies.

The structure of this document is as follows:

clauses and subclauses preceded by ■ indicate no additional conditions to EN 1559‑1:2011 or

EN 1559‑2:2014

NOTE When additional information is given in a clause or subclause of this document (versus the same clause or subclause of EN 1559‑1:2011 or EN 1559‑2:2014) it is preceded by: "ln addition to EN 1559:".

subclauses and paragraphs marked with a single dot • indicate that the conditions shall be agreed at the time of enquiry and order;
subclauses marked with two dots •• indicate that conditions may be agreed at the time of enquiry and order (optional);
subclauses without dot marking are mandatory.

1 Scope

This document applies to corrosion resistant steel castings for general purposes.

This document relates to castings manufactured from martensitic, austenitic, fully austenitic and

austenitic-ferritic steel grades characterized by their chemical composition (see Table 1) and mechanical properties (see Table 2).

ln cases where castings are joined by welding by the founder, this document applies.

ln cases where castings are welded:

to wrought products (plates, tubes, forgings);
or by non-founders,

this document does not apply.

2 Normative references

3 ■ Terms and definitions

4 ■ Information to be supplied by the purchaser

5 Designations

6 Manufacture

6.1 Manufacturing process

6.2 Welding operations

6.3 ■ Further processing

7 Requirements

7.1 ■ General

7.2 Material

7.3 ■ Casting

7.4 Corrosion behaviour

8 Inspection

8.1 General

8.2 ■Type of inspection document and type of inspection

8.3 ■Test unit

8.4 ■ Samples

8.5 Test procedures

8.6 ■ Invalidation of test results

8.7 ■ Retests

8.8 ■ Sorting and reprocessing

9 ■ Marking

10 ■ Packaging and surface protection

11 ■ Complaints

12 Supplementary information

Bibliography

BS EN 10283:2019

Corrosion resistant steel castings

Current

Published:

30 Apr 2019