National foreword

This Published Document is the UK implementation of CEN/TS 19100‑3:2021.

The UK participation in its preparation was entrusted to Technical Committee B/525/-/11, Structural Glass.

A list of organizations represented on this committee can be obtained on request to its committee manager.

The UK committee draws users’ attention to National Annex NA, which provides further guidance to assist users in the application of this document.

Contractual and legal considerations

This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be accepted by BSI in relation to the adequacy, accuracy, completeness or reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law.

This publication is provided as is, and is to be used at the recipient’s own risk.

The recipient is advised to consider seeking professional guidance with respect to its use of this publication.

This publication is not intended to constitute a contract. Users are responsible for its correct application.

This publication is not to be regarded as a British Standard.

Compliance with a Published Document cannot confer immunity from legal obligations.

This Published Document was published under the authority of the Standards Policy and Strategy Committee on 29 February 2024.

This Technical Specification (CEN/TS) was approved by CEN on 25 July 2021 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

European foreword

This document (CEN/TS 19100‑3:2021) has been prepared by Technical Committee CEN/TC 250 “Structural Euro-codes”, the secretariat of which is held by BSI. CEN/TC 250 is responsible for all Structural Eurocodes and has been assigned responsibility for structural and geotechnical design matters by CEN.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under Mandate M/515 given to CEN by the European Commission and the European Free Trade Association.

This document has been drafted to be used in conjunction with relevant execution, material, product and test standards, and to identify requirements for execution, materials, products and testing that are relied upon by this document.

Any feedback and questions on this document should be directed to the users’ national standards body. A complete listing of these bodies can be found on the CEN website.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

0 Introduction

0.1 Introduction to the Eurocodes

0.2 Introduction to CEN/TS 19100-1 (all parts)

0.3 Introduction to CEN/TS 19100-3

0.4 Verbal forms used in the Eurocodes

0.5 National annex for CEN/TS 19100-3

1 Scope

1.1 Scope of CEN/TS 19100‑3

(1) This document gives design rules for mechanically supported glass components primarily subjected to in-plane loading. It also covers construction rules for mechanical joints for in-plane loaded glass components.

NOTE In-plane loaded glass elements are primarily subjected to in-plane loads, e.g. transferred from adjacent parts of a structure. They can also be subjected to out-of-plane loading.

1.2 Assumptions

(1) The assumptions of EN 1990 apply to this document.

(2) This document is intended to be used in conjunction with EN 1990, EN 1991 (all parts), EN 1993‑1‑1, EN 1995‑1‑1, EN 1998‑1, EN 1999‑1‑1 and EN 12488.

2 Normative references

3 Terms, definitions and symbols

3.1 Terms and definitions

3.2 Symbols and abbreviations

4 Basis of design

4.1 Requirements

4.2 Fracture Limit State (FLS) verification

4.3 Post Fracture Limit State (PFLS) verification

5 Materials

6 Durability

7 Structural analysis and detailing

7.1 Structural modelling for analysis

7.2 Effects of deformed geometry of the structure

7.3 Consideration of imperfections

7.4 Interlayers of laminated glass

7.5 Temperature effect and long-term effect

7.6 Detailing

8 Limit states including ULS, FLS and PFLS

8.1 General

8.2 Dynamic effects in FLS

9 Serviceability limit states

10 Joints and Connections

10.1 General

10.2 Sleeve bearings

10.3 Lapped splices with bolts in shear

10.4 Friction connections

Bibliography

PD CEN/TS 19100-3:2021

Design of glass structures - Design of in-plane loaded glass components and their mechanical joints

Current

Published:

31 Dec 2024